歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

多槽超聲波清洗機清洗不規則噴絲板注意以下五點

作者：admin來源：http://www.dijiushangdian.cn/時間：2020-12-14

多槽超聲波清洗機適用于油漆、陶瓷和軟質材料。可用于電子元器件、電鍍、五金、手表、表帶、工具、光學鏡片、寶石、噴絲板、眼鏡框、半導體硅片、旋轉濾嘴及玻璃制品、手機配件、汽車維修等。但是用多槽超聲波清洗機清洗不規則噴絲板注意以下五點。

Multi groove ultrasonic cleaning machine is suitable for paint, ceramics and soft materials. It can be used in electronic components, electroplating, hardware, watch, watch strap, tool, optical lens, gem, spinneret, eyeglass frame, semiconductor silicon chip, rotary filter and glass products, mobile phone accessories, automobile maintenance, etc. However, when cleaning the irregular spinneret with multi slot ultrasonic cleaning machine, pay attention to the following five points.

多槽超聲波清洗機機

Multi slot ultrasonic cleaning machine

1、多槽超聲波清洗機清洗時間

1. Cleaning time of multi tank ultrasonic cleaning machine

清洗時間的設定因噴絲板和產品的不同而不同。設定正確的時間，可以節省時間，達到好的清潔效果(通常設定的時間為10-20分鐘)。

The setting of cleaning time varies with spinneret and product. Setting the right time can save time and achieve good cleaning effect (usually the setting time is 10-20 minutes).

如果時間太短，工件就不能清洗。如果時間過長，水洗后的樣品表面會出現空化斑點，影響表面光潔度。

If the time is too short, the workpiece cannot be cleaned. If the time is too long, cavitation spots will appear on the surface of the sample after washing, which will affect the surface finish.

2、多槽超聲波清洗機清洗溫度因素

2. Cleaning temperature factors of multi tank ultrasonic cleaning machine

由于每個不規則噴絲板的物理特性不同，清洗時需要選擇不同的清洗溫度。例如，油脂一般超過50攝氏度，但對于鋁件，一般選擇40攝氏度左右比較合適。溫度太高了。氧化斑點形成，但在有毛刺的情況下，一般建議選擇小于15攝氏度的。用多槽超聲波清洗機清洗不規則噴絲板注意以下五點。

Due to the different physical characteristics of each irregular spinneret, different cleaning temperature should be selected. For example, the grease is generally over 50 ℃, but for aluminum parts, it is more appropriate to choose about 40 ℃. The temperature is too high. Oxidation spots are formed, but in the case of burr, it is generally recommended to choose the one less than 15 ℃. Clean irregular spinneret with multi slot ultrasonic cleaning machine, pay attention to the following five points.

3、多槽超聲波清洗機頻率

3. Multi slot ultrasonic cleaning machine frequency

多槽超聲波清洗機超聲波頻率一般在25KHZ到130KHZ之間。使用水或水超聲波清洗噴絲板清洗劑時由空化引起的物理清洗功率對低頻明顯有利，一般在15-30kHz左右。清潔有小縫隙、狹縫和深孔的噴絲板。建議使用幾百kHz的高頻(通常為40kHz或更多)。請使用400kHz來保養手表噴絲板。使用寬帶調頻清洗時，效果會更好。

The ultrasonic frequency of multi slot ultrasonic cleaning machine is generally between 25kHz and 130KHz. When using water or water ultrasonic to clean spinneret cleaner, the physical cleaning power caused by cavitation is obviously beneficial to the low frequency, which is generally about 15-30KHZ. Clean spinneret with small gaps, slits and deep holes. A high frequency of several hundred kHz (usually 40 kHz or more) is recommended. Please use 400kHz to maintain the watch spinneret. When using broadband FM cleaning, the effect will be better.

4、超聲波清潔力

4. Ultrasonic cleaning power

標準多槽超聲波清洗機的功率范圍從100W到1500W。大功率產品主要用于清洗五金、機械等行業，或用于重污染的常見噴絲板。

The power range of standard multi slot ultrasonic cleaning machine is from 100W to 1500W. High power products are mainly used for cleaning hardware, machinery and other industries, or for heavy pollution common spinneret.

5、超聲波清洗解決方案

5. Ultrasonic cleaning solution

選擇正確的清潔溶液可以幫助你清潔不規則噴絲板。傳統的清洗溶液(介質)包括水基溶液和有機溶液，如酒精和汽油。目前的多槽超聲波清洗機超聲波清洗劑是各種清洗劑、潤濕劑和其他可回收組分的混合物。

Choosing the right cleaning solution can help you clean the irregular spinneret. Traditional cleaning solutions (media) include water-based solutions and organic solutions, such as alcohol and gasoline. At present, the ultrasonic cleaning agent of multi tank ultrasonic cleaning machine is a mixture of various cleaning agents, wetting agents and other recyclable components.

可以選擇一些優秀的針對性多槽超聲波清洗機清洗劑，達到適當的清洗效果，防止噴絲板和(清洗液)發生反應。

Some excellent targeted multi slot ultrasonic cleaning agent can be selected to achieve proper cleaning effect and prevent the spinneret from reacting with (cleaning fluid).

上一篇：超聲波清洗機在小物件清洗方面的應用
下一篇：超聲波清洗機設備是如何清洗鍵盤的?