歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

安裝全自動超聲波清洗設備的注意事項

作者：admin來源：http://www.dijiushangdian.cn/時間：2022-08-05

全自動超聲波清洗設備在很多行業都有應用，不僅僅是因為它效果好，重要的它大大節省了企業成本。為了更好的應用全自動超聲波清洗設備，下面先給大家介紹一下全自動超聲波清洗設備。

Full automatic ultrasonic cleaning equipment has been applied in many industries, not only because of its good effect, but also because it greatly saves enterprise costs. In order to better apply the full-automatic ultrasonic cleaning equipment, let's first introduce the full-automatic ultrasonic cleaning equipment.

做好預備工作和噴沙處理

Make preparations and sand blasting

在正式的地進行全自動超聲波清洗機的安裝前，要把所需膠接的超聲波換能器（配好對的）、膠水等應該一一的先準備就緒。同時應該把所需膠接的超聲波換能器、缸體進行噴沙處置，噴沙膠接面必須達到要求以及噴沙使用一定要求的金剛沙，對于沙子的要求比較高，比如要精挑細選、保持枯燥等等；且噴沙時緊縮空氣的壓力應注意調整到規定要求，并經過氣源處置器去濕后的高壓空氣。

Before the formal installation of the full-automatic ultrasonic cleaning machine, the required adhesive ultrasonic transducers (equipped with the right ones), glue, etc. should be prepared one by one. At the same time, the ultrasonic transducer and cylinder body that need to be bonded should be sandblasted. The sandblasting bonding surface must meet the requirements and the diamond sand with certain requirements should be used for sandblasting. The requirements for sand are relatively high, such as careful selection, keeping dry, etc; In addition, the pressure of compressed air during sand blasting should be adjusted to the specified requirements, and the high-pressure air after dehumidification through the air source processor.
全自動超聲波清洗機

應進行相關的清洗工作

Relevant cleaning shall be carried out

要把噴好沙的缸體和全自動超聲波清洗機先停止下來做好清洗，后者要用準備好的溶液進行清洗，基本的要去除外表的一些塵垢，再拿丙酮進行下一遍的清洗工作。同時注意超聲波清洗機的缸體需要先后進行多遍清洗過程，涼干后再拿專門的溶液各進行一次漂洗，網墊的厚度應該要合乎要求，并且將不銹鋼網異樣清洗潔凈備用。

Stop the sand sprayed cylinder block and the full-automatic ultrasonic cleaning machine first, and the latter should be cleaned with the prepared solution. Basically, remove some dust on the surface, and then take acetone for the next cleaning. At the same time, it should be noted that the cylinder body of the ultrasonic cleaning machine needs to be cleaned several times successively, and then rinse with a special solution after it is dry. The thickness of the mesh pad should meet the requirements, and the stainless steel mesh should be cleaned differently for standby.

做好烘干、預熱處理

Do a good job of drying and preheating

要把清洗好的超聲波換能器和缸體及網墊放入烘箱進行烘干，烘干溫度也要控制在相應的范圍內，然后烘干2小時后冷卻到某個溫度時進行膠接。在一切膠接預備任務做好后，注意要配好膠水（常溫）充沛諧和后疾速進行膠接。

Put the cleaned ultrasonic transducer, cylinder block and mesh mat into the oven for drying, and the drying temperature should be controlled within the corresponding range. Then, after drying for 2 hours, when it is cooled to a certain temperature, conduct bonding. After all bonding preparation tasks are completed, pay attention to prepare the glue (normal temperature) and carry out bonding quickly after full harmony.

安裝全自動超聲波清洗設備的注意事項大體就是這樣了，如果您對此有什么疑問的話就來關注我們網站www.dijiushangdian.cn吧，有關人員為您講解更多。

The precautions for installing automatic ultrasonic cleaning equipment are generally like this. If you have any questions about this, please follow our website www.dijiushangdian.cn, and relevant personnel will explain more to you.

上一篇：全自動硅料清洗設備機使用的七點注意
下一篇：超聲波清洗機水溫調到多少比較好