歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

全自動超聲波清洗機盲孔的清洗要注意

作者：admin來源：http://www.dijiushangdian.cn/時間：2022-04-18

　　全自動超聲波清洗機的零部件還是挺多的，所以在清洗的時候需要多加注意，那么全自動超聲波清洗機盲孔的清洗要注意什么呢？只有多了解才能正確的操作！

　　Automatic ultrasonic cleaning machine parts or a lot of, so in the cleaning time need to pay more attention to, then automatic ultrasonic cleaning machine blind hole cleaning to pay attention to what? Only more understanding can correct operation!

　　在設計全自動超聲波清洗機時，可以在罐體上加一個壓縮空氣噴嘴。外部工廠氣源，在清洗盲孔零件時，將工件慢慢放入，盡可能讓水流入孔內。零件放置后，利用壓縮空氣使水產生大量水柱沖擊工件。為了使堵塞在孔口中的氣泡爆裂，達到更好的對盲孔部位的超聲波清洗效果。

　　In the design of automatic ultrasonic cleaning machine, a compressed air nozzle can be added to the tank body. External factory air source, when cleaning the blind hole parts, slowly put the workpiece into the hole, as much as possible to let the water flow into the hole. After the parts are placed, compressed air is used to generate a large number of water columns to impact the workpiece. In order to make the bubbles blocked in the orifice burst, to achieve a better ultrasonic cleaning effect on the blind hole.

　　使用中高頻結合的超聲波清洗機。利用高頻超聲波，原理是高頻振蕩，使堵塞在盲孔中的氣體超聲波清洗機的氣泡破裂，鐵屑被一掃而空。

　　The use of high frequency combined with ultrasonic cleaning machine. The use of high frequency ultrasonic, the principle is high frequency oscillation, so that blocked in the blind hole in the gas ultrasonic cleaning machine bubble burst, iron filings were swept away.

　　一般情況下，全自動超聲波清洗機使用時的頻率在很大程度上決定了超聲波清洗機的清洗效果。超聲波空化閾值與超聲波清洗機的頻率密切相關，頻率越高，氣蝕閥越高。也就是說：頻率越低越容易產生空化，而在頻率低的情況下，液體被壓縮變薄的時間間隔更長，這樣氣泡在解體前就可以長到更大的尺寸.因此，我們可以通過增加空化強度來提高清洗效率。

　　In general, the frequency of automatic ultrasonic cleaning machine largely determines the cleaning effect of ultrasonic cleaning machine. Ultrasonic cavitation threshold is closely related to the frequency of ultrasonic cleaning machine, the higher the frequency, the higher the cavitation valve. That is: cavitation is more likely to occur at lower frequencies, and at lower frequencies, the liquid is compressed and thinned at longer intervals, allowing bubbles to grow to larger sizes before they disintegrate. Therefore, we can increase the cleaning efficiency by increasing the cavitation intensity.

　　盲孔太小，水壓無法使堵在盲孔中的氣泡爆裂，超聲波的傳播是以水為介質，即超聲波清洗機說只要水能到達的地方，超聲波就會存在，從而實現清洗。但少量未滲入清洗劑的盲孔無法清洗干凈。

　　The blind hole is too small, the water pressure can not make the bubble blocked in the blind hole burst, the transmission of ultrasonic is water as the medium, that is, ultrasonic cleaning machine said that as long as water can reach the place, ultrasonic will exist, so as to achieve cleaning. However, a small number of blind holes that have not infiltrated into the cleaning agent cannot be cleaned.

　　全自動超聲波清洗機盲孔的清洗要注意什么呢？以上的講解內容便是問題的詳解了，如果您還有清洗機什么方面的清洗事項不懂的，那就來我們網站www.dijiushangdian.cn咨詢吧！

　　What should we pay attention to when cleaning the blind hole of automatic ultrasonic cleaning machine? The above explanation is a detailed explanation of the problem, if you have a cleaning machine what aspects of cleaning matters do not understand, then come to our website www.dijiushangdian.cn consultation!

上一篇：超聲波清洗機的使用對人有危害嗎？
下一篇：噴淋清洗機在清洗零部件時要測試什么？